Buy 1.8" Thread M2.5 Extension Probe Tip CMM Touch Probe Stylus Replacement for PGFUN CNC 3D Touch Probe(1-pack) Online at Lowest Price Ever in India

Product From USA

new | 1.8" Thread M2.5 Extension Probe Tip CMM Touch Probe Stylus Replacement for PGFUN CNC 3D Touch Probe(1-pack)

Brand : PGFUN

new | 1.8" Thread M2.5 Extension Probe Tip CMM Touch Probe Stylus Replacement for PGFUN CNC 3D Touch Probe(1-pack)

Brand : PGFUN

Condition new
Asin B0BG4T39B5
Category Industrial & Scientific
Subcategory Test Probes & Leads
Leafcategory TOOLS
MPN TR004110_40
Origin USA
Brandname PGFUN
Height 1.5748
Length 0.19685
Width 0.19685
Weight 1

Condition	new
Asin	B0BG4T39B5
Category	Industrial & Scientific
Subcategory	Test Probes & Leads
Leafcategory	TOOLS
MPN	TR004110_40
Origin	USA
Brandname	PGFUN
Height	1.5748
Length	0.19685
Width	0.19685
Weight	1

This is the M2.5 1.8" Tungsten Steel Probe Tip/ Stylus Replacement for PGFUN 3D Edge Finder CNC Touch Probe

Main Specs: Thread-M2.5 x 4.5mm/ 0.18" (length), Ball Dia: 2mm/ 0.08 in, Total Length: 51.5mm/ 2 inch

Note: to ensure accuracy, concentricity needs to be adjusted after changing the probe tip every time.

Any Question, Free to Contact Us.

#478 in Test Probes & Leads

#117508 in Industrial & Scientific

1.8" Probe Tip Replacement for PGFUN V6 Anti-roll 3D Touch Probe New Upgraded Waterproof Edge Finder

Specification:
Power: DC5-24V
NPN-NO/NPN-NC Wiring: Red-VCC (DC5-24V power), Yellow: IO/ Signal Output, Black- GND(DCM)
Repeatability Accuracy: 0.01 mm/ 0.0004 in.
Feedrate: 50-200 mm/min.
Approach Direction: ±X, ±Y, +Z.
Over Travel Protection Distance: X- ± 4mm/0.16 in , Y- ±4mm/ 0.16 in, , Z- 2mm/ 0.08 in.
Lifetime: > 3 million triggers.
Material: fine frosted black oxidized aluminum alloy with a flat surface anti-roll design.
Fit for: Mach3 and GRBL
Package Include: 3D touch probe x 1, cable x 1, allen wrench x 1, straight probe tip x 1.

Software Recommendation for 3D Probe
If you are using a mach3 system, it is recommended to use the open source Probe Wizard or ProbeIt
If you are using the grbl system, it is recommended to use GRBLGRU.

FAQs:
Q1: Need to turn on the spindle speed?
A1: Definitely no, or it'll cause data tolerance.

Q2: Why is the concentricity different when the probe is installed?
A2: Because the low-accuracy spring collet can't guarantee 100% positive position. After each installation of the probe, even if the concentricity is adjusted to 10 μm, there will still be deviations when the probe is re-installed. So it is best to use a AAA or higher accuracy ER spring collect (run-out tolerance <0.0002") for your chuck. It is recommended that use a high-precision gauge to check the concentricity after installing the chuck.

Q3: i need a NO touch probe, can i use this one?
A3: No, you can buy the Edge Finder-NC version