product-image
product-image
product-image
product-image
    1
    2
    3
    4
    5
    6
flagProduct From USA  
new | OCESTORE ILI9341 2.8" SPI TFT LCD Display Touch Panel 240X320 Module with PCB 5V/3.3V STM32 with Touch
Brand : OCESTORE
new | OCESTORE ILI9341 2.8" SPI TFT LCD Display Touch Panel 240X320 Module with PCB 5V/3.3V STM32 with Touch
Brand : OCESTORE
Product Specifications
Conditionnew
AsinB09574L9JJ
CategoryElectronics
SubcategoryMonitors
LeafcategoryMONITOR
MPNILI9341
OriginUSA
BrandnameOCESTORE
Weight1
Display Size2.8 inches
Display TypeLCD
Product Details
2.8" 240x320 SPI TFT LCD Serial Port Module With PCB Adapter Micro SD ILI9341 5V/3.3V 2.8 inch LED Display For Arduino
Product Description
2.8" 240x320 SPI TFT LCD Serial Port Module With PCB Adapter Micro SD ILI9341 5V/3.3V 2.8 inch LED Display For Arduino
Product description:
2.8 inch color screen, support 16BIT RGB 65K color display, display rich colors
320X240 resolution, optional touch function
Using SPI serial bus, only a few IO can light up the display
With SD card slot for easy expansion experiment
Product parameters:
Display color: RGB 65K color
With touch: MSP2807
Size: 2.8 (inch)
Type: TFT
Driver chip: ILI9341
Resolution: 320*240 (Pixel)
Module interface: 4-wire SPI interface
Effective display area (AA area): 43.2x57.6 (mm)
Module PCB bottom plate size: 50.0x86.0 (mm)
Working temperature: -20 ℃ ~ 60 ℃
Storage temperature: -30 ℃ ~ 70 ℃
VCC power supply voltage: 3.3V ~ 5V
Logic IO port voltage: 3.3V (TTL)
Power consumption: about 90mA
Interface definition:
VCC: 5V / 3.3V power input
GND: ground
CS: LCD screen chip select signal, low level enable
RESET: LCD screen reset signal, low level reset
DC / RS: LCD screen register / data selection signal, low level: register, high level: data
SDI (MOSI): SPI bus write data signal
SCK: SPI bus clock signal
LED: Backlight control, high-level lighting, if no control is required, then connect to 3.3V
SDO (MISO): SPI bus read data signal, if you do not need the read function, you can not connect
(The
following is the wiring of the touch screen signal line, if there is no
need to touch or the module itself does not have a touch function, it
may not be connected)
T_CLK: touch SPI bus clock signal
T_CS: touch screen chip select signal, low level enable
T_DIN: touch SPI bus input
T_DO: touch SPI bus output
T_IRQ: touch screen interrupt signal, low level when touch is detected
Product Description
2.8" 240x320 SPI TFT LCD Serial Port Module With PCB Adapter Micro SD ILI9341 5V/3.3V 2.8 inch LED Display For Arduino
Product description:
2.8 inch color screen, support 16BIT RGB 65K color display, display rich colors
320X240 resolution, optional touch function
Using SPI serial bus, only a few IO can light up the display
With SD card slot for easy expansion experiment
Product parameters:
Display color: RGB 65K color
With touch: MSP2807
Size: 2.8 (inch)
Type: TFT
Driver chip: ILI9341
Resolution: 320*240 (Pixel)
Module interface: 4-wire SPI interface
Effective display area (AA area): 43.2x57.6 (mm)
Module PCB bottom plate size: 50.0x86.0 (mm)
Working temperature: -20 ℃ ~ 60 ℃
Storage temperature: -30 ℃ ~ 70 ℃
VCC power supply voltage: 3.3V ~ 5V
Logic IO port voltage: 3.3V (TTL)
Power consumption: about 90mA
Interface definition:
VCC: 5V / 3.3V power input
GND: ground
CS: LCD screen chip select signal, low level enable
RESET: LCD screen reset signal, low level reset
DC / RS: LCD screen register / data selection signal, low level: register, high level: data
SDI (MOSI): SPI bus write data signal
SCK: SPI bus clock signal
LED: Backlight control, high-level lighting, if no control is required, then connect to 3.3V
SDO (MISO): SPI bus read data signal, if you do not need the read function, you can not connect
(The
following is the wiring of the touch screen signal line, if there is no
need to touch or the module itself does not have a touch function, it
may not be connected)
T_CLK: touch SPI bus clock signal
T_CS: touch screen chip select signal, low level enable
T_DIN: touch SPI bus input
T_DO: touch SPI bus output
T_IRQ: touch screen interrupt signal, low level when touch is detected