product-image
product-image
product-image
product-image
    1
    2
    3
    4
    5
    6
flagProduct From USA  
new | SparkFun 16x2 SerLCD, RGB Text, Qwiic; Red, Green, Blue Text on Black Display, 3.3v Logic & Power
Brand : SparkFun
new | SparkFun 16x2 SerLCD, RGB Text, Qwiic; Red, Green, Blue Text on Black Display, 3.3v Logic & Power
Brand : SparkFun
Product Specifications
Conditionnew
AsinB08H9PY88T
CategoryElectronics
SubcategorySingle Board Computers
LeafcategoryBISS Basic
MPNLCD-16397
ColorBlack
OriginUSA
BrandnameSparkFun
Height0.59
Length1.5
Width3.19
Weight1
Product Details
16x2, RGB on Black Display. Three communication options: Serial, I2C and SPI. Adjustable I2C address controlled via software special commands (0x72 default). Qwiic connection.
The AVR ATMega328p (with compatible with Arduino bootloader) is populated on the back of each LCD screen and handles all of the LCD control. Open-sourced firmware and compatible with Arduino bootloader enables updates via the IDE
Emergency reset to factory settings (Jumper RX to GND on bootup). Operational backspace character. Incoming buffer stores up to 80 characters
Pulse width modulation of backlight allows direct control of backlight brightness and current consumption. Pulse width modulation of contrast allows for software-defined contrast amount.
User-definable splash screen. Dimensions (LxWxH): 80.02x36.13x14.27mm. Weight: 0.0779 oz.
What's Inside The Box ?
Qwiic connector, 16-pin header
Product Ranking
#3233 in Single Board Computers (Computers & Accessories)
Product Description
The SparkFun SerLCD is an AVR-based, serial enabled LCD that provides a simple and cost effective solution for adding a 16x2 RGB on Black Liquid Crystal Display into your project. We've seriously overhauled the PCB design on the back of the screen by including an ATmega328P that handles all of the screen control, meaning a backpack is no longer needed! This display can now communicate in three different ways: serial, I2C, and SPI. This comes equipped with a Qwiic connector, bringing serial LCDs into the Qwiic ecosystem. This simplifies the number of wires needed and allows your project to display all kinds of text and numbers.
The on-board ATmega328P AVR microcontroller utilizes 11.0592 MHz crystal for greater communication accuracy with adjustable baud rates of 1200 through 1000000 but is default set at 9600. The firmware for this SerLCD is fully opensource and allows for any customizations you may need.
Note: Since the SerLCD is a 3.3V device, please make sure you convert to 3.3V logic depending on your chosen microcontroller or single board computer. Otherwise, you may risk damaging your board.
The SparkFun Qwiic Connect System is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong.
Product Description
The SparkFun SerLCD is an AVR-based, serial enabled LCD that provides a simple and cost effective solution for adding a 16x2 RGB on Black Liquid Crystal Display into your project. We've seriously overhauled the PCB design on the back of the screen by including an ATmega328P that handles all of the screen control, meaning a backpack is no longer needed! This display can now communicate in three different ways: serial, I2C, and SPI. This comes equipped with a Qwiic connector, bringing serial LCDs into the Qwiic ecosystem. This simplifies the number of wires needed and allows your project to display all kinds of text and numbers.
The on-board ATmega328P AVR microcontroller utilizes 11.0592 MHz crystal for greater communication accuracy with adjustable baud rates of 1200 through 1000000 but is default set at 9600. The firmware for this SerLCD is fully opensource and allows for any customizations you may need.
Note: Since the SerLCD is a 3.3V device, please make sure you convert to 3.3V logic depending on your chosen microcontroller or single board computer. Otherwise, you may risk damaging your board.
The SparkFun Qwiic Connect System is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong.