1 x RFID reader and 3 x RFID tags (one S50 white card + two key rings)
Original Philips MFRC522 chip
new | DIYables RC522 RFID Reader and RFID Card for Arduino, ESP32, ESP8266, Raspberry Pi
Brand : DIYables
new | DIYables RC522 RFID Reader and RFID Card for Arduino, ESP32, ESP8266, Raspberry Pi
Brand : DIYables
Availability :
Out Of Stock
Click to connect with our customer support
Product Specifications
| Condition | new |
|---|---|
| Asin | B0B33Y87ZG |
| Category | Electronics |
| Subcategory | Single Board Computers |
| MPN | DIY-RFID-KIT-13 |
| Connector Type | Pin Headers |
| Origin | USA |
| Brandname | DIYables |
| Weight | 1 |
Product Details
Works with Arduino, ESP32, ESP8266, Raspberry Pi
Interface: SPI
Operating frequency: 13.56MHz
Product Ranking
#6074 in Single Board Computers (Computers & Accessories)
Product Description
This is a RC522 RFID kit that work with Arduino, ESP32, ESP8266, Raspberry Pi, or any 5V or 3.3V microcontroller. The kit includes 1 RFID reader and 3 RFID tags. PACKAGE includes: - 1 x RC522 RFID Reader Module - 1 x S50 White RFID Card (RFID tag) - 2 x RFID Key Ring (RFID tag) - 1 x straight pin header - 1 x right-angle pin header SPECIFICATION: - Original Philips MFRC522 chip - Works with Arduino, ESP32, ESP8266, Raspberry Pi - Power supply: +3.3V - Interface: SPI - Operating frequency: 13.56MHz TUTORIALS: - Arduino and ESP32 online tutorials: DIYables RFID Kit INTERFACE: - GND pin: connect this pin to GND (0V) - VCC pin: connect this pin to VCC (3.3) - RST pin: is a pin for reset and power-down. When this pin goes low, hard power-down is enabled. On the rising edge, the module is reset. - IRQ pin: is an interrupt pin that can alert the microcontroller when RFID tag comes into its detection range. - MISO pin: SPI interface, connect this pin to MOSI of microcontroller - MOSI pin: SPI interface, connect this pin to MISO of microcontroller. - SCK pin: SPI interface, connect this pin to SCK of microcontroller - SS pin: SPI interface, connect this pin to CS (SS) of microcontroller NOTE: The RC522 RFID Reader Module has NOT pre-soldered to the pin header. This allows users to use straight pin header, right-angle pin header, or any cables
Product Description
This is a RC522 RFID kit that work with Arduino, ESP32, ESP8266, Raspberry Pi, or any 5V or 3.3V microcontroller. The kit includes 1 RFID reader and 3 RFID tags. PACKAGE includes: - 1 x RC522 RFID Reader Module - 1 x S50 White RFID Card (RFID tag) - 2 x RFID Key Ring (RFID tag) - 1 x straight pin header - 1 x right-angle pin header SPECIFICATION: - Original Philips MFRC522 chip - Works with Arduino, ESP32, ESP8266, Raspberry Pi - Power supply: +3.3V - Interface: SPI - Operating frequency: 13.56MHz TUTORIALS: - Arduino and ESP32 online tutorials: DIYables RFID Kit INTERFACE: - GND pin: connect this pin to GND (0V) - VCC pin: connect this pin to VCC (3.3) - RST pin: is a pin for reset and power-down. When this pin goes low, hard power-down is enabled. On the rising edge, the module is reset. - IRQ pin: is an interrupt pin that can alert the microcontroller when RFID tag comes into its detection range. - MISO pin: SPI interface, connect this pin to MOSI of microcontroller - MOSI pin: SPI interface, connect this pin to MISO of microcontroller. - SCK pin: SPI interface, connect this pin to SCK of microcontroller - SS pin: SPI interface, connect this pin to CS (SS) of microcontroller NOTE: The RC522 RFID Reader Module has NOT pre-soldered to the pin header. This allows users to use straight pin header, right-angle pin header, or any cables
